Note: All products and shipping fees in our store do not include tax. If you have any questions, please consult our customer service before placing an order!
How to inflate correctly
Before inflating, use a small tool to hold the inflation core and completely release the remaining gas inside to eliminate the pressure in the lighter gas tank.
2. Press the outlet of the gas tank vertically downward for about 5 seconds each time, and do it two or three times.
After inflation is completed, please wait for about 3 to 5 minutes before using it. If it still won't ignite after 5 minutes, just increase the adjustment valve a little. (Pay attention to the + -) direction.
For more details, please refer to the following detailed introduction.
Special reminder: In plateau areas above 1,000 meters in altitude, the use of inflatable windproof lighters and direct lighters will all be affected. The proportion of the decline in ignition rate is large. Please choose a windproof direct-flush lighter with caution. Try to use open flames or kerosene lighters.
I. Detailed Inflation Introduction:
Gas filling method
When refueling, there must be no sparks or fire sources around to ensure safety. Never smoke while refueling.
2. Qualified butane gas should be used. Inferior gas may damage the lighter or reduce its service life.
3. When refueling a regular model, please turn the lighter upside down, align the gas outlet of the gas cylinder with and cover the gas inlet of the lighter, and press it several times with force, holding for about 2 seconds each time. If the gas cannot be refilled, it might be that there is excess air remaining in the gas tank. At this point, you can release the gas. Use a small screwdriver to quickly release the gas at the air inlet 1-2 times, and then proceed with the refilling operation.
4. When refueling the loudspeaker, please first loosen the screw cover of the air inlet with a flat-head screwdriver or other tools, and then follow the above steps. After the gas filling is completed, just tighten the screw cap. Do not tighten it too much. Otherwise, it will result in the hood not being tightly closed and the sound from the hood not being clear, and it will also cause gas to escape. The high-end type of loudspeaker should be equipped with a dedicated air nozzle for air filling. 5. When refueling a gasoline engine, the hood should be opened, the engine pulled out and the movement turned upside down. Lift the outer sponge and add an appropriate amount of gasoline. After the gasoline seeps into the inner sponge, cover it with the outer sponge and then insert it into the engine housing.
6. After refilling any type of lighter, it is necessary to wait for at least one minute to allow the temperature of the newly filled gas to adjust to room temperature. Only after the residual gas attached to the outside of the lighter has completely evaporated can it be ignited. If the ignition operation is carried out immediately at this moment, the residual gas on the surface of the lighter may catch fire, causing unnecessary danger. After replenishing the gas, if the flame height is too high or too low during use, it is a normal phenomenon and the flame height can be adjusted moderately.
Adjust the flame
When in use, as the gas content of the product decreases and the ambient temperature changes, the flame height will change to a certain extent. This is a normal phenomenon and you can adjust the flame height moderately.
2. When in use, the normal flame height should be adjusted to; Windproof and direct-flush lighters are 1.5 to 2.5 centimeters long. Lighters with loud sounds, gasoline and open flames should be 2.5 to 4.0 centimeters long.
3. If it is necessary to adjust the height of the flame, please align a flat-head screwdriver with the groove of the flame regulator. If the lighter itself is equipped with an adjustment ring, you can directly adjust it with your finger. Turn it in the direction of the (-) arrow, that is, clockwise, to lower the flame height. Turning in the direction of the (+) arrow, that is, counterclockwise, can increase the height of the flame. Note: Rotate counterclockwise. Do not exceed half a turn from the normal flame height. Otherwise, it may damage this product.
4. The flame height of a gasoline lighter should be controlled by adjusting the height of the ignition wick. If the flame height is too high, you can cut off a small amount of the wick with scissors. If the flame height is too low, you can pull out the wick appropriately.
Precautions
1. Contains pressurized flammable gas. Keep out of reach of children.
2. Do not puncture or play with lighters. Do not throw them into fire.
3. Please use in a well-ventilated environment and be cautious of flammable materials.
4. The fire head must not be directed towards flammable substances such as the face, skin or clothing to avoid danger.
5. When igniting, please identify the position of the ignition outlet and press the ignition button appropriately. Lighters of different styles are ignited in different ways: they are divided into direct ignition, side ignition and side ignition. For gasoline engines, the grinding wheel should be quickly rubbed. For sound machines, the thumb should be used to quickly rub the drum from right to left.
6. When in use, if cigarette ash or other debris accidentally falls into the fire outlet, blow hard to remove the debris in time; otherwise, it may cause poor ignition.
7. When the lid of a gasoline lighter is opened, the gas starts to escape. Therefore, when not ignited, please make sure to tightly close the hood for storage.
8. This product is not suitable for lighting. Do not burn continuously for more than 1 minute to avoid scalding the skin due to high temperatures.
9. Do not leave the lighter in a high-temperature environment for a long time (50 degrees Celsius / 122 degrees Fahrenheit), and avoid direct sunlight for a long time, such as around stoves, in outdoor closed unmanned vehicles and trunks.
Due to the climatic restrictions on combustion conditions in areas above 3,000 meters in altitude, the ignition of windproof and direct-flush lighters may be significantly affected. At this time, it is recommended to use an open flame lighter.
When using tabletop and other handicraft lighters, the positions of the flame outlet, ignition, air inlet and flame regulator should be clearly identified to ensure correct operation
12. Qualified butane gas should be used. Inferior gas may damage the lighter or reduce its service life.
